Electro Industries Shark 200T Spezifikationen Seite 88
- Seite / 298
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Doc# E149701 5 - 10
5: Communication Installation
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Valid Communication Settings are as follows:
COM1 (IrDA)
Response Delay (0-750 msec)
COM2 (RS485)
Address (1-247; for DNP ONLY 1 - 65520)
Protocol (Modbus RTU, Modbus ASCII or DNP)
Baud Rate (1200 to 57600) Your meter must have Runtime Firmware Version
26 or higher to set Baud rates of 1200, 2400, and 4800.
Response Delay (0-750 msec)
Parity (Odd, Even, or None) Your meter must have Runtime Firmware
version 26 or higher to be able to set Parity.
DNP Options for Voltage, Current, and Power - these fields allow you to choose Pri-
mary or Secondary Units for DNP, and to set custom scaling if you choose Primary.
Click the Optimal Scaling button to have the software choose a divisor for voltage,
current, and power, that will not result in an over/under-range.
NOTE: You must set the DNP polling software to multiply by the divisor amount
before showing the final value.
See Chapter 5 in the Communicator EXT
TM
User Manual for more information.
8. When changes are complete, click the Update Device button to send a new profile
to the meter.
9. Click Exit to leave the Device Profile or click other menu items to change other
aspects of the Device Profile (see the following section for instructions).
- Shark 200 & 200T 1
- Use Of Product for Protection 6
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- 1.1.1: Wye Connection 13
- 1.1.2: Delta Connection 16
- 1.2: Power, Energy and Demand 20
- 1.4: Harmonic Distortion 26
- 1.5: Power Quality 29
- 2.1.2: Ordering Information 34
- 2.1.3: V-Switch 36
- Key Technology 36
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 60
- OJDLFMQMBUFE 60
- CSBTTTUVET 60
- 5.1.1: IrDA Port (Com 1) 79
- Electro Industries/GaugeTech 80
- UNICOM 2500 83
- Overview 84
- Software 85
- 6: Using the Shark® 200 Meter 103
- 6.2: Using the Front Panel 105
- 6.2.6: Using Operating Mode 117
- 7: Using the I/O Option Cards 121
- 7.2: Installing Option Cards 122
- 7.4: 1mA Output Card (1mAOS) 124
- 7.4.1: Specifications: 124
- 7.4.2: Default Configuration: 125
- 7.4.3: Wiring Diagram 126
- 7.5.1: Specifications 127
- 7.5.2: Default Configuration: 128
- 7.5.3: Wiring Diagram 129
- 7.6.1: Specifications 130
- 7.6.2: Wiring Diagram 132
- 7.7.1: Specifications 133
- 7.7.2: Default Configuration: 134
- 7.7.3: Wiring Diagram 135
- 7.8.1: Specifications 136
- 7.8.2: Wiring Diagram 137
- 7.9.1: Specifications 138
- 7.9.2: Default Configuration 139
- 7.9.3: Wiring Diagram 139
- 7.10.1: Specifications 140
- 7.10.2: Default Configuration 141
- 7.10.3: Wiring Diagram 141
- 8.1: Overview 143
- 8.2: Hardware Connection 143
- 8.4.1: Ethernet Communication 144
- 8.4.2: Embedded Web Server 144
- 8.4.5: Keep-Alive Feature 151
- 9: Data Logging 153
- A.1: Introduction 155
- B.1: Introduction 161
- B.3: Data Formats 161
- B.4: Floating Point Values 162
- Byte 012345678910111213 164
- B.5.3: Block Definitions 166
- B.5.4: Log Retrieval 176
- B.5.4.1: Auto-Increment 176
- B.5.6: Examples 196
- B.6.1: Hex Representation 199
- B.6.2: Decimal Representation 199
- C: DNP Mapping 243
- C.3: Data Link Layer 244
- C.4: Application Layer 244
- C.5: Error Reply 246
- C.6: Object Specifics 246
- C.7: DNP Object Point Map 248
- C.8: DNP Message Layouts 257
- C.9: Internal Indication Bits 260
- D.1: Introduction 261
- D.2: Installation Procedures 261
- Network Card (INP300S) 269
- E.1.5: Reference Materials 280
- Network Card 281
- E.2.1: Overview 281
- System Log 293
- Firmware 294
- E.6: Keep-Alive Feature 296
- E.7: Testing 296
- E.8: Error Codes 297
Verwandte Produkte und Handbücher für Multimeter Electro Industries Shark 200T
(246 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern