Electro Industries Shark 200T Bedienungsanleitung PDF herunterladen (Seite 8)

Specifications

Voltage Inputs

• 20-576 Volts Line To Neutral,

0-721 Volts Line to Line

• Universal Voltage Input

• Input Withstand Capability – Meets

IEEE C37.90.1 (Surge Withstand

Capability)

• Programmable Voltage Range to

Any PT ratio

• Supports: 3 Element WYE, 2.5

Element WYE, 2 Element Delta, 4

Wire Delta Systems

• Burden: Input Impedance 1 Mega

Ohms. Burden 0.014W at 120 Volts

• Input wire gauge max (AWG

12 / 2.5mm

)

Current Inputs

• Class 10: (0.005 to 11) A, 5 Amp

Nominal

• Class 2: (0.001 to 2) A, 1A Nominal

Secondary

• Fault Current Withstand (at 23°C):

100 Amps for 10 Seconds, 300

Amps for 3 Seconds, 500 Amps for

1 Second

• Continuous current withstand:

20 Amps for Screw Terminated or

Pass Through Connections

• Programmable Current to Any

CT Ratio

• Burden 0.005VA per phase Max at

11Amps

• Pickup Current: 0.1% of Nominal

Class 10: 5mA

Class 2: 1mA

• Pass through wire diameter:

0.177” / 4.5mm

Isolation

All Inputs and Outputs are

galvanically isolated to 2500 Volts

Environmental Rating

Storage: (-20 to +70)° C

Operating: (-20 to +70)° C

Humidity: to 95% RH Non-Condensing

Faceplate Rating: NEMA12

(Water Resistant)

Mounting Gasket Included

Sensing Method

• True RMS

• Sampling at over 400 samples /

cycle on all channels of measured

readings simultaneously

• Harmonics resolution to 40th order

• Waveform up to 512 samples/cycle

Update Rate

• Watts, VAR and VA - every 6 cycles

• All other parameters - every 60

cycles

Power Supply

Option D2:

• (90 to 265) Volts AC and (100 to 370)

Volts DC. Universal AC/DC Supply

Option D:

• (18-60) Volts DC (24-48 VDC Systems)

Burden: 10VA Max

Standard Communication Format

• 2 Com Ports (Back and Faceplate)

• RS485 Port (Through Backplate)

• IrDA (Through Faceplate)

• Com Port Baud Rate: (1200 - 57600)

• Com Port Address: 1-247

• 8 Bit, No parity

• Modbus RTU, ASCII or DNP 3.0

Protocols

KYZ Pulse

• Type Form C Contact

• On Resistance: 35 Ohms Max

• Peak Voltage: 350 VDC

• Continuous Load Current: 120mA

• Peak Load Current: 350mA (10ms)

• Off State Leakage Current@

350VDC: 1uA

Dimensions and Shipping

• Weight: 2 lbs

• Basic Unit: H4.85" x W4.85" x L4.25"

• Shark® 200 meter mounts in 92mm

DIN & ANSI C39.1 4" round cut-outs

• Shark® 200T Transducer DIN rail

mounted

• 2-inch DIN Rail Included

• Shipping Container Dimensions:

6” cube

Meter Accuracy

• See page 2

• Note: For 2.5 element programmed

units, degrade accuracy by an

additional 0.5% of reading.

• Note: For 1A (Class 2) Nominal,

degrade accuracy to 0.5% of reading

for watts and energy; all other values 2

times rated accuracy.

Compliance

• IEC 62053-22 (0.2% Accuracy)

• ANSI C12.20 (0.2% Accuracy)

• ANSI (IEEE) C37.90.1 Surge

Withstand

• ANSI C62.41 (Burst)

• EN61000-6-2 – Immunity for

Industrial Environments: 2005

• EN61000-6-4 – Emission Standards

for Industrial Environments: 2007

• EN61326-1 - EMC Requirements:

2006

Electro Industries/GaugeTech

1800 Shames Drive • Westbury, NY 11590

1- 877- EIMETER (1- 877-346-3837) • E-Mail: [email protected]

Tel: 516-334 -0870 • Web Site: www.electroind.com • Fax: 516-338-4741

Model Frequency Current Input V-Switch Pack

Shark200

(Meter/Transducer)

Shark200T

(Transducer Only)

All fields must be filled in to create a valid part number.

Additional Accessories

Option

Numbers:

Example: Shark200

50 Hz

System

60 Hz

System

10 Amp

Secondary

2 Amp

Secondary

Multifunction

Meter Only

Standard Data-

Logging Memory

Power Quality Harmonics

Limits & Control

64 Samples/cycle

Waveform Recording

512 Samples/cycle

Waveform Recording

Power Supply

90-265V

AC/DC

18-60V

Communication Converters

9PINC – RS232 Cable

CAB6490 - USB to IrDA Adapter

Unicom 2500 - RS485 to RS232 Converter

Unicom 2500-F – RS485 to RS232 to Fiber Optic

Converter

Modem Manager, Model #, MM1 – RS485 to RS232

Converter for Modem Communication

IrDA232 - IrDA to RS232 Adapter for Remote Read

Compliance Documents

Certificate of Calibration, Part #: CCal – This provides

Certificate of Calibration with NIST traceable Test Data.

Current Transformer Kits

CT200K – 200/5 Ratio 1.00” Window 3 CTs

CT400K – 400/5 Ratio, 1.25” Window, 3 CTs

CT800K – 800/5 Ratio, 2.06” Window, 3 CTs

CT2000K – 2000/5 Ratio, 3.00” Window, 3 CTs

CT Specifications:

Frequency: 50 to 400Hz; Insulation: 600 Volts, 10kV BIL

Flexible Leads: UL 1015 105°C, CSA Approved, 24”

Long, #16AWG

Software Option Numbers

COMEXT3 – CommunicatorEXT 3.0 for Windows®

* Consult factory application engineer for additional

transformer ratios, types or window sizes.

I/O Slot 1* I/O Slot 2*

INP100S

None

RO1S

2 Relays /

2 Status

PO1S

4 Pulses /

4 Status

1mAOS

4 channel

Analog Output

0-1

(bidirectional)

20mAOS

4 Channel

Analog Output

4-20mA

FOSTS

Fiber Optic

Output ST

Terminated

FOVPS

Fiber Optic

Output VPIN

Terminated

INP100S

100BaseT

Ethernet

None

RO1S

2 Relays /

2 Status

PO1S

4 Pulses /

4 Status

1mAOS

4 channel

Analog Output

0-1

(bidirectional)

20mAOS

4 Channel

Analog Output

4-20mA

FOSTS

Fiber Optic

Output ST

Terminated

FOVPS

Fiber Optic

Output VPIN

Terminated

INP100S

100BaseT

Ethernet

* I/O cards can be ordered separately

using the above part numbers.

E149702 031113 V.1.21

Ordering Information

Mounting

(Shark® 200 Only)

ANSI Mounting

DIN

DIN Mounting

Brackets

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Electro Industries Shark 200T Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimeter Electro Industries Shark 200T