Electro Industries Shark 200T Spezifikationen PDF herunterladen (Seite 215)

B: Modbus Map and Retrieving Logs

Doc# E149701 MM-27

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg

Modbus Address

Hex Decimal

write only in PS update mode

7CFF - 7CFF 32000 - 32000 Class ID of the Option Card 1 Settings UINT16 bit-mapped -------- cccctttt Which class (cccc) and type(tttt) of card the Option

Settings for Card 1 apply to. See note 22.

7D00 - 7D3E 32001 - 32063 Settings for Option Card 1, First Overlay -- see

below

7D3F - 7F3E 32064 - 32575 Settings for Option Card 1, Second Overlay --

see below

512

Block Size: 576

First Overlay write only in PS update mode

7D00 - 7D00 32001 - 32001 Slave address UINT16 1~247 (for Modbus)

1~65534 (for DNP)

none Slave address of the unit. The communication capable

card is always a master.

Set to 0 when an analog board is installed.

7D01 - 7D01 32002 - 32002 Speed and format UINT16 bit-mapped

-abcde--fghijklm

Bps: a=57600; b=38400; c=19200; d=14400; e=9600

Stop bits 'f': cleared 1 stop bit, set 2 stop bits

Parity: g=even; h=odd; i=none

Data bits: j=8; k=7; l=6; m=5

Set to 0 when an analog board is installed.

7D02 - 7D02 32003 - 32003 Reserved Reserved 1

7D03 - 7D03 32004 - 32004 Protocol UINT16 bit-mapped

-------- -----ppp-

ppp= 100 =DNP3; 010=Ascii Modbus; 001=Rtu Modbus

Set to 0 when an analog board is installed.

7D04 - 7D04 32005 - 32005 Reply delay UINT16 0 to 65535 milliseconds Delay to reply to a Modbus transaction after receiving it.

Set to 0 when an analog board is installed

7D05 - 7D3E 32006 - 32063 Reserved Reserved 58

Block Size: 63

First Overlay write only in PS update mode

7D00 - 7D00 32001 - 32001 Input#1 - 2 bindings & logging enables UINT16 bit-mapped

-------- 2222 1111

One nibble for each input.

Assuming "abcc" as the bits in each nibble:

"a": select this input for EOI (End Of Interval)pulse

sensing.

"b": log this input when pulse is detected

"cc": Input event trigger mode - Contact sensing method;

00 = none; 01 = op

en to close; 10 = close to open; 11 =

any change.

Every input has an associated internal accumulator (See

input Accumulator Scaling), which is incremented every

time the input changes according with the trigger mode

crieteria “cc”

7D01

7D01 32002 - 32002 Relay #1 Delay to Operate UINT16 0.1 second units Delay to operate the relay since request. 1

7D02 - 7D02 32003 - 32003 Relay #1 Delay to Release UINT16 0.1 second units Delay to release the relay since request. 1

7D03 - 7D08 32004 - 32009 Reserved UINT16 Set to 0. 6

7D09 - 7D09 32010 - 32010 Relay #2 Delay to Operate UINT16 0.1 second units Delay to operate the relay since request. 1

7D0A - 7D0A 32011 - 32011 Relay #2 Delay to Release UINT16 0.1 second units Delay to release the relay since request. 1

7D0B - 7D20 32012 - 32033 Reserved UINT16 Set to 0. 22

Overlays for Option Card 1 Programmable Settings

Settings Registers for any communication capable card, including network and analog cards

Settings Registers for Digital I/O Relay Card

Programmable Settings for Option Card 1

Option Card 1 Setups Block

1 2 ... 210 211 212 213 214 215 216 217 218 219 220 ... 245 246

Kommentare zu diesen Handbüchern

Keine Kommentare

Electro Industries Shark 200T Spezifikationen Seite 215

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimeter Electro Industries Shark 200T