Electro Industries Shark 200T Spezifikationen PDF herunterladen (Seite 208)

B: Modbus Map and Retrieving Logs

Doc# E149701 MM-20

Electro Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg

Modbus Address

Hex Decimal

read-only except as indicated

2B3F - 2B3F 11072 - 11072 Digital Input States UINT16 bit-mapped

dddd cccc bbbb aaaa

Nibble "dddd" for input#4, "cccc" for input#3, "bbbb" for

input#2 and "aaaa" for input#1.

Within each field, right most bit is the current state

(1=closed, 0=open), and bits at left are the older states

100ms apart. (historical states)

Example:

xxxx xxxx xxxx 0011

Current state of input#1 is closed, before that it was

closed too, before that it was open and the oldest state

known is open.

2B40 - 2B40 11073 - 11073 Digital Output States UINT16 bit-mapped

-------- ----4321

One bit for each output. Bit 4 is for output #4, and bit 1 is

for output #1. If a bit is set the output is closed,

otherwise it is opened.

2B41 - 2B41 11074 - 11074 Pulse Output Test Select UINT16 bit-mapped

-------- ----4321

Write 1 to a bit to set its corresponding Pulse Output into

test mode. Write 0 to restore it to normal operation. A

privileged session is required to write the bits. Reading

this register reports the mode for each output (1=under

test, 0=normal).

2B42 - 2B42 11075 - 11075 Pulse Output Test Power UINT16 bit-mapped

ddvvvvvv vvvvvvvv

This register is Writeable in privileged session only.

Simulates constant Power for the Pulse Output under

test. Format is same as Kt settings for Pulse Output.

"V" is raw value in Wh/pulse from 0 to 9999.

"dd"=decimal point

osition: 00=0.XXXX, 01=X.XXX,

10=XX.XX, 11= XXX.X

2B43

2B46 11076 - 11079 Reserved Reserved 4

2B47 - 2B47 11080 - 11080 Input 1 Accumulator, Scaled UINT16 0 to 9999 1

2B48 - 2B48 11081 - 11081 Input 2 Accumulator, Scaled UINT16 0 to 9999 1

2B49 - 2B49 11082 - 11082 Input 3 Accumulator, Scaled UINT16 0 to 9999 1

2B4A - 2B4A 11083 - 11083 Input 4 Accumulator, Scaled UINT16 0 to 9999 1

2B4B - 2B4B 11084 - 11084 Output 1 Accumulator, Scaled UINT16 0 to 9999 1

2B4C - 2B4C 11085 - 11085 Output 2 Accumulator, Scaled UINT16 0 to 9999 1

2B4D - 2B4D 11086 - 11086 Output 3 Accumulator, Scaled UINT16 0 to 9999 1

2B4E - 2B4E 11087 - 11087 Output 4 Accumulator, Scaled UINT16 0 to 9999 1

2B4F - 2B78 11088 - 11129 Reserved Reserved 42

Block Size: 58

read-only

2B3F - 2B3F 11072 - 11072 Status of card UINT16 bit-mapped

----cf-- --------

Flag fields:

c=calibration not good; f=configuration error

2B40 - 2B78 11073 - 11129 Reserved UINT16 Reserved 57

Block Size: 58

Data and Control Block--Analog Out 0-1mA / Analog Out 4-20mA (Note 15)

Data and Control Block -- Digital I/O Pulse Output Card Overlay (Note 15)

resolution is 1, 10, 100, 1000,

10000, or 100000 counts

Disabled accumulators always read 0.

1 2 ... 203 204 205 206 207 208 209 210 211 212 213 ... 245 246

Kommentare zu diesen Handbüchern

Keine Kommentare

Electro Industries Shark 200T Spezifikationen Seite 208

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Multimeter Electro Industries Shark 200T